Do not let your older Motorola Portable radios suffer, Send them to The Portable Clinc for a Check-up or Repair.

If you want only programming done We will program your radio or radios for a fixed rate of $33.00 per hour with a 2 hour min. for as many radios as can be programmed in that time. The normal time to setup and program a radio is about 30 miniutes each including checking it out on the Service Monitor.  Shipping of the Radios back to you will be at your expense. I like to ship using 2 - 3 day Priority Mail. We can also ship using UPS or Fed-X.  We Service and program the following models but can Service other models also. Email me with your needs. Presently We can SERVICE, PROGRAM or RECRYSTAL the following Motorola HT220,MT500,MT1000,HT600,P100,P200,HT90,HT440,SP50,GP300,GP350,P110,P1225, Saber1,2,3 ,HT1000,and Other simular models. We also Repair and Program Motorola Mobiles like Maxtrac, GM300 and GM350, M1225,CDM1550LS, Syntor X9000 Mobiles and some of the older crystal controlled modiels like the the Maxar80 Mobiles, Moxy Mobiles, and Mocom70 Mobiles,


I am not selling the MT500 8 freq VHF kit as the coils are not available and would cost to much to substitute. The MT500 VHF Synthesizer is almost ready for to start Selling. I am waiting for the final version of Software to program it.The way you will program it is to connect Your computers Serial Port to the radio and running a program that I will supply. The Synthesizer will make a VHF MT500 a 16 channel radio that you can enter the Frequencies and PL codes that you want for each channel. The Synthesizer will be a assembled kit because most of it is surface mounted parts that you can mount in your radio and will have a A/B Band switch for 8 channels each. There is also a Green Led for Freq Lock and s phono jack for plugging in the Programming cable. Iam only selling the first version for the VHF Ham Channels but it will work for other ranges and bands. After I have had time to check it out completely on the 2 meter band. I will also offering a UHF version in the near future. The cost of the Kit will be around $150.00 dollars or less if possible. I will also Install the Kit for you if you desire it for $99.00 more. The MT500 has a coil tuned front end and will only cover about 4 MHz with out any loss of Band Spread Q. unlike the new radios that are being sold today that cover great band spreads and have no tuned front ends this one will be very selective.

Send your requests to:
This email address is being protected from spam bots, you need Javascript enabled to view it
Or This email address is being protected from spam bots, you need Javascript enabled to view it
Or call me at 561 703 0696 

You have two choices for getting your Communication System working using a RoIP Radio Internet connection. You Can  uses a new Commercial Router type Product that VoiceInterop offers that does not require a dedicated Computer to get your Radio System up and working and uses Commercial Software they provide.  Option two is  use the RoIP B2  if you have a Router with E&M Signaling or the RoIP-B3 modules on this site using NON Commercial EQSO Software products that I have to offer for your use.   I have been working with VoiceInterop  to develop   new simple Radio to Internet Interface Products (RoIP) that works great .  You must connect the RoIP-B3  Unit  to a  Computer to make it work.   The RoIP-B3 connects your Radio Base Station or Portable Radio  to a  Computer that connects to the Internet using your Computers  Sound Card and Serial Port.    The Unit is easy to set up with your radios and work great using 600 ohm Line interface transformers to isolate the Computer audio circuits  from the Radios audio circuits.   Solid state Relays are used to operate the PTT of the radio to keep the radio ground system from the Computer ground system.  A RJ45 connector  Provides all the needed  connections to your Radio.  I designed the RoIP Products to work with both Portable and Mobile 2-way Motorola Radios but will work with any Radio.  There is a  item to talk about and that is if you are using Microsoft Windows XP operation System I have found that you need a to use a USB to RS232 serial converter cable to work with our products.  I do have the Converter cables in stock and they cost $40.00 or you can get one at your local computer store. I am designing  a new product that will have the USB interface built in  and I will  add in  a USB sound card feature also. But for now I recommend  you use the converter cable set to Com3 or Com4  to provide the Serial interface need for keying the radio.

Model RoIP-B2 Cost $199.00

E&M Signaling Version designed to connect a Mobile or Base Station radio to Cisco Router if you aleady have one with E&M signaling features.   I presently do not supply the Housing like the one in the Picture. I am designing a new one that will cost $25.00 more if there is a demand for it.  Send  Email or Call me if you are interested and have questions.                         Phone 561-703-0696 Ask for Bob Hicks

Model RoIP-B3 Cost $199.00

This module is the was designed  for Point to Point or many Points to Many Points  Linking of Your Radio Systems which lets you Send Radio Audio both ways over the Internet and gives you Push-to-Talk (PTT) in both directions.  You must have a Conputer connected at both ends of the Internet to make this model work.  This unit has Voice Operated Squech (VOX) using the provided software and Carrier Operated Squelch(COS/COR) Features.  This Model will  operate your Portable and Mobile and Base Station Radios using the Internet.  If you have been using  Leased Lines this will save you a lot of money as long as you have Your Internet running.   I  presently do not supply the white Housing like the one in the Picture.  I am designing a new one that will cost $25.00 more for future units when there is enough demand for it .    Send Email or Call me if you are interested and have questions.   Phone 561-703-0696 Ask for Bob Hicks

New products are available for Commercial use from:

VoiceInterop.com

Check out the new Web Site above. You can get a lot of Good Information. They have a new Router Product called AudioMate 360 that will connect your Radio System directly to the Internet with out the need of a  dedicated computer  and uses Commercial Software that they provide. They also provide the Server Service that will be Rock Stable and will give you World Wide Radio and Phone Service to your Remote Sites any  place on the Our Planet that has internet service.

  You may also contact us about VoiceIntrop Products or the ones  on this web site. 

Computer Creations,Corp.

Contact: Robert Hicks President

e-Mail:  This email address is being protected from spam bots, you need Javascript enabled to view it

Phone:  561-703-0696 Cell  Anytime ok  

Address:  20 Wood Ridge Drive-- Ocala, Florida 34482

VoiceInterop will  provide you with a interface to the Internet and  Telephone Phone Networks using their  newly developed Servers and Software.

For Ham use We will offer these new products from The Portable Clinic's new online Store now in development. Presently the cost is $199.00 which includes a assembled unit. a 9V Power  Supply is provided if needed plus 2 audio cables and a RS232 cable to connect to your computer.  You will need to build a Radio interface cable to connect your radio interface to the new product or you can order one from US by request. We can supply a cable with  We will also build a special cable for your Radio for $50.00  For Ham use you can use the RoIP-B3 product  using ECHOLINK OR EQSO'S Software that connects to the Ham worldwide network. I like the EQSO software because you can set up your own Server by using NO-IP.com create a Static IP that will not change for your Server. Using EQSP also allows you to create  and set up Channels  or rooms using there software version with a built in DTMF software decoder if you have DTMF on your Radio  ECHO-LINK Software works great and is very stable.  I use ECHO Link for my Personal Ham use and EQSO for my Private Network. I have a older version of the EQSO Software that is not longer exceptable for HAM use but works great for a Personal System.

Current Up todate Software: 

Echolinik SOFTWARE web site for Windows (Ham use only!)

EQSO SOFTWARE web site for Windows (Ham use only!)

EQSO SOFTWARE X web site for Linux (Ham use only!)

I am using this product myself. I have used these products with the Motorola MT500, HT600, MT1000 Portables and Maxtrac type Mobiles that have a 16 or 20 pin interface connector on the back of the Radio. The Motorola CDM Radio products have a 20 pin connector on the back that does the same.   These Products will operate with other Radio Manufactures that have a way to connect to the same Radio features as the Motorola Radios provide. They can be interfaced to any Two-way Radio Base Station, Mobile, or Portable.

We can supply interface cables for Radios also if needed.

I will keep you informed on the progress of these New Products. The RoIP-B3 Product comes assembled  and tested and are about (2" by 5").  The Connections are very simple (Line-in) and (Line-out) with adjustment Pots for both and Connection to your computers Audio interface and RS232 Port for Radio-PTT and (COS)Computer operated Squelch.  The interface will work from any DC power Source of 5v to 15v and I have modfied the Products so it will be powered directly from your Radios power Source .  Two LED show(RED-PTT) and (Green-COS). 

RoIP Items  on this site are Products Designed for

VoiceIntrop Corp.

Computer Creations Corp. designed these products and is a Sales and provides Engineering Support for VoiceInterop .  You may contact Us at Computer Creations Corp .  If you have any questions about these products by Phone or Email see our Contact Section.

The Above pictures show the RoIP-B3 model. 

You can Setup a RoIP B1  Radio System using a Portable Radio like the ones below or any Two-way Portable that has a Speaker and Microphone Jack with access to the PTT circuit of the radio. Radios that come with Remote Microphone features will do the job.   The RoIP-B3 Model costs $199.00 and comes with 2 audio cables and a RS232 Serial cable to connect to your computer to the B3 unit.  A 15v Power Supply is provided  to power the RoIP-B3 Unit.  We will supply Software that will get you going. You will need to build or Purchase a cable to connect your radio to the RoIP-B3. Talk to us about building one for your radio.

 
The Model RoIP-B3 Costs $199.00 and  Works Great with Radios like the ones below using the 16-pin connector on the Back of the Motorola Radios. You can build a cable or Order one from us for  $50.00 Ready to go.  We supply audio cables and a RS232 cable  to connect the RoIP=B3 Model to Your Computer for PTT.  This Model has a Computer operated Relay (COR) feature that the B1 or Portable Radio model does not have. The COR feature is used to send a PTT type signal to the internet when you talk to your base station unit using your Local Radio system..